|
Contact Information
Telephone
+32
(0)3 722 91 60
Fax
+32
(0)3 722 91 66
Postal
address
Zakstraat
104
9112
Sinaai
Belgium
Electronic
mail
info@proxtech.com
|
| | Installation
instructions for COMPACT
modules
Dimensions
Module
 
Antenna
Wired 125 kHz antenna
Etched
pcb 13,56 MHz antenna
PIN
connections
|
PIN
|
MIFARE
13,56MHz
|
LEGIC
13,56MHz
|
HITAG/EM
125kHz
|
Antenna
pcb
|
| 1
|
REC_ANT
|
NC
|
REC_ANT
|
ANT4
|
| 2
|
TX1_ANT
|
TX_ANT
|
TX1_ANT
|
ANT1
|
| 3
|
UB
+5V
|
UB
+5V
|
UB
+5V
|
|
| 4
|
GND_ANT
|
GND_ANT
|
GND_ANT
|
ANT2
|
| 5
|
TX2_ANT
|
GND
|
TX2_ANT
|
ANT3
|
| 6
|
GND
|
GND
|
GND
|
|
| 7
|
TEST_PIN_OUT
|
TEST_PIN_OUT
|
TEST_PIN_OUT
|
|
| 8
|
TEST_PIN_IN
|
TEST_PIN_IN
|
TEST_PIN_IN
|
|
| 9
|
SDA
DIGITAL I/O 5
|
SDA
DIGITAL I/O 5
|
SDA
DIGITAL I/O 5
|
|
| 10
|
SCL
DIGITAL I/O 6
|
SCL
DIGITAL I/O 6
|
SCL
DIGITAL I/O 6
|
|
| 11
|
RX,
DATA, D1
|
RX,
DATA, D1
|
RX,
DATA, D1
|
|
| 12
|
TX,
CLOCK, D0
|
TX,
CLOCK, D0
|
TX,
CLOCK, D0
|
|
| 13
|
Card
Load, Direction
|
Card
Load, Direction
|
Card
Load, Direction
|
|
| 14
|
DIGITAL
I/O 1
|
DIGITAL
I/O 1
|
DIGITAL
I/O 1
|
|
| 15
|
/RESET
|
/RESET
|
/RESET
|
|
| 16
|
DIGITAL
I/O 2
|
DIGITAL
I/O 2
|
DIGITAL
I/O 2
|
|
| 17
|
DIGITAL
I/O 3
|
DIGITAL
I/O 3
|
DIGITAL
I/O 3
|
|
| 18
|
DIGITAL
I/O 4
|
DIGITAL
I/O 4
|
DIGITAL
I/O 4
|
|
| 19
|
GND
|
GND
|
GND
|
|
| 20
|
UB
+5V
|
UB
+5V
|
UB
+5V
|
|
NOTE
The function of the
I/O pins depends on the firmware in the reader module. For customer-specific
requirements, please forward your needs for further study.
Also the function
of the data output pins ( pin 11, 12 and 13 ) depends on the firmware. Please
check the module version for correct information on this. Note that the output
signals are always on TTL level. Eventual buffer circuits or level transformers
must be connected externally.
- For
Clock/Data :
-
pin
11 = Clock
- pin 12
= Data
- pin 13
= Card Load Signal (low
for +/- 0.5 s for every newly detected tag
)
- For
Wiegand :
-
pin
11 = Data0
- pin 12
= Data1
- pin 13
= Card Load Signal (low
for +/- 0.5 s for every newly detected tag
)
- For
RS232(RS485) :
-
pin
11 = TX
- pin 12
= RX
- pin 13
= Direction (controls DE signal for RS485 drivers )
|
